SHEFFIELD / A USEFUL START
Tell us what the part will face.
Start with heat, movement, environment, load and orientation. A material name is only part of a complete brief.
Conditions to questions
| Describe | Useful information to send | Decision it informs |
|---|---|---|
| Heat | Expected part temperature, source of heat and duration; include brief peaks and normal use | Which grade data and later evaluation are relevant |
| Movement | Where it bends, slides or rotates; travel and frequency | Flexible body versus a joint, wear surfaces and geometry |
| Environment | Indoor/outdoor use; daylight, water, humidity and named cleaning products | Exposure information needed for a specific grade |
| Load | Direction, contact area, support points, magnitude if known, and time under load | Section shape and the relationship between load and layers |
| Orientation | Visible faces, important holes, contact faces and inaccessible cavities | Surface priorities, layer direction and support-removal access |
| Fit and size | Dimensions with units, mating components, permitted movement and overall envelope | A usable design brief rather than a guessed universal tolerance |
Material families: a starting vocabulary
Availability of any named grade must be confirmed for the order. The manufacturers below are sources of technical education; they are not an equipment or supplier list for this workshop.
| Family | What it can help you discuss | What still needs asking |
|---|---|---|
| PLA | Detailed visual models and early form exploration | Does heat or repeated bending make this particular grade inappropriate? |
| PETG | A common filament route for practical forms | What finish, stiffness and exposure requirements actually apply? |
| ASA / ABS | Engineering thermoplastics worth comparing for demanding environments | ASA’s UV behaviour differs from ABS; specify exposure and exact grade rather than a universal outdoor promise |
| PA / nylon | Wear, movement and tough-part questions | Moisture handling and grade-specific properties matter |
| PC and blends | Another technical filament family | Confirm process compatibility and the actual data sheet, not properties inferred from the family name |
| TPU / other flexible families | Compliant shapes, contact and movement | Hardness, geometry, recovery and the actual loading sequence |
| Resin formulations | Detailed forms and distinct specialist behaviours | Exact formulation and prescribed preparation/post-cure; no blanket toughness assumption |
Sources: Prusa PLA, PETG, ASA, polyamide, material guide, flexible materials, Formlabs post-curing. These brief family summaries are not suitability approvals.
Read the conditions behind a data sheet
A stated property belongs to a particular material and test method. Look for specimen geometry, print orientation, preparation, conditioning and how the value was measured. Heat-deflection data is not a universal continuous-use temperature, and elongation at break is not a repeat-bending design limit. These distinctions matter when moving from a data-sheet specimen to the clip or lever shown here. UltiMaker TPU 95A data sheet.
For a resin part, use the grade’s applicable processing information. Post-curing can alter properties and dimensions, and the appropriate conditions depend on the formulation. Do not transfer one resin’s figures to another. Formlabs guidance.
Orientation: more than turning a model
Build orientation changes the relationship between the part and the layer planes. It also changes support contact and visible surfaces. Identify the function and the important faces before treating a print position as settled. Prusa modelling guidance.
In the lever comparison, the relevant question is how the pivot is held and where the force acts. In the flexible clip, the movement of the opening and contact with the cable matter. These are different briefs even if the same printer could produce both.
The illustrated layer bands are simplified. They do not show actual wall count, infill, toolpaths or material properties. A local model/preview image cannot establish performance. Dimensions, material grade and intended conditions are needed before a meaningful physical evaluation can be planned.
A better starting brief
Download the blank part-conditions outline. Add the model revision and units, sketch the force and supports, identify critical surfaces, and state which decisions are still open. It is fine to start with an unanswered question; label it instead of filling it with a guess.
If the model is ready, start a print quote. If the shape needs creating or changing, use the CAD enquiry route. Explore the questions in context through our two hypothetical design studies.
